ARE Study Review

Which of the following detector types can detect smoke or a smoldering fire that has not yet burst into flames? A. Ionization B. Rise-of-temperature C. Photoelectric D. Flame detectors

What is the difference between life-cycle cost analysis (LCC) and life-cycle assessment analysis (LCA)?

A soil's density can provide an indication of its strength. To increase load-bearing capacity what does soil modification often seek to reduce in soil?

While underimprovement describes property that is not being put to its highest and best use (reducing its value), when does overimprovement apply?

During construction, how does the owner unilaterally order changes to the contract without changing its terms? A by change order document B by issuing a written order for a minor change C by construction change directive D by issuing an addendum E none of the above

⭕ What material is used for drainage pipes with a diameter more than 42 inches? A. vitrified clay B. concrete C. cast iron D. PVC

The 2007 editions of AIA construction contract forms A101, A102(A111 old) and A201 introduced and defined the term Initial Decision Maker (IDM). The role is designated to make decisions in all matters of dispute between the Owner and the Contractor. These decisions are final and binding, but are also subject to mediation and arbitration. If the IDM is not appointed in the construction agreement, who will serve this function?

How can the Architect be compensated if the Owner continues to use the Architect's Instruments of Service in order to complete the project after the Architect agreement has been terminated (either at the Owner's convenience or by the Architect)?

What are the three appearance grades, not designations of structural properties , available for glued-laminated wood members?

What is tern plate, which is sometimes used for roofing and flashing, made of?

What does a 1.0 sabin indicate about the absorptivity per square foot of a surface?

How are quantities shown on drawings? Choose the most correct answer. A. documented with drawing notes B. implicitly C. explicitly enumerated D. with product references

AIA A201 contains a clause precluding the contract parties from seeking to recover any loss that is already covered by property insurance from each of the other parties. How is this identified? A. waiver of liens B. release of liens C. waiver of subrogation D. retainage

Why may an owner reject, or consider "unresponsive", a bid that proposes more than the requirements in the documents?

To specify an accessible sink, the depth of the basin should be a maximum of ________. Choose two of the following: A. 5.5 inches depth in a counter 33 inches high. B. 6 inches deep. C. 6.5 inches depth in a counter 34 inches high. D. 7 in deep in a counter 35 inches high. E. 7.5 in deep in a counter 36 inches high.

An owner may authorize a change in services for which a written scope of duties is attached to the owner-architect contract, to provide a higher degree of monitoring or observing work on site than expected under basic construction phase services for architect's site visits. What is this role and when does it occur?

Which one of the following designed this modern thin shell concrete dome supported by Y-shaped flying buttresses? A. Rafael Gustavino B. Pier Luigi Nervi C. Eugene Freyssinet D. Oleg Kerensky

In this section, a ceiling assembly separates the attic space above from the room interior below. If the building is located in Lewisville, Texas (hot-humid zone), where is the predicted location of condensation and what is the predicted condition of the gypsum board in this assembly? (Select 2 from the following) A. outside face of vapor retarder B. inside face of vapor retarder C. gypsum board will be wet D. gypsum board will be dry

What is the shape of a shear diagram when the value of shear is constant? A. constant slope line, B. horizontal C. vertical, D. parabolic

How are many municipal or public building projects financed?

The following ducts sizes (inches) are given as rough equivalents to deliver the same CFM. Based on shape, which offers the least resistance to air movement and the least friction? A. 5x12, B. 6x10, C. 7x8, D. 9 dia.

Although exact angles differ by the 4 major climatic regions, what is the optimum orientation for a rectangular building to maximize solar heat gain in winter months, minimize solar heat gain in summer months and minimize exposure to winter winds? A. Long side facing east, B. Short side oriented east-west, C. Long side oriented east-west, D. Short side facing north

What is lacking in a temperate climate?

Find the reactions indicated in the beam diagram. ( ∑M = 0 ; Moment sum of loads and resisting reaction is equal to zero.)

y What types of materials have no yield points?

Which offers the longest span limits: LH, DLH, or K?

Identify from top to bottom: 1. 2. 3. 4. 5.

In AIA document A201, remaining retainage is not due until the Contractor submits a number of items indemnifying the Owner against claims from subcontractors. If a Subcontractor refuses to furnish a release or waiver required by the Owner, what can the Contractor furnish to indemnify the Owner against the subcontractors lien?

In building industry language, the term "abatement" is often used in relation to inhibiting or reducing pollutant matter such as dust or asbestos. In planning and pre-design issues, abatement may be defined as:

What are two common voltages supplied to larger buildings for primary electrical service from a utility company?

What is the minimum spacing of bolts specified by AISC? and preferred spacing? A. 1 1/4 times the diameter of the bolt; 2 times preferred B. 1 3/4 times the diameter of the bolt; 2 1/4 times preferred C. 2 1/3 times the diameter of the bolt; 2 2/3 times preferred D. 2 2/3 times the diameter of the bolt; 3 times preferred E. 3 times the diameter of the bolt; 3.25 times preferred

Which of the following footings is commonly used when a series of columns is adjacent to the property line but there is not enough space for a symmetrically loaded footing (can't overlap the neighboring property)? A. independent column footing B. combined footing C. strap footing D. cantilever footing E. raft foundation

Match each of the letters with one of these elements: head, bottom rail, stile, top rail, mullion, pane, drip cap, glazing bead, clear opening, apron

Which of the following dispute resolution options offers a low risk exercise, less formal and more private process: A. arbitration, B. mediation, C. litigation

In a materials reference showroom, an area of study carrels is set aside for industry professionals to review product literature and reference materials. The showroom's reference center is open from 7 am through 10 pm every day and the owners of the center would like to reduce the energy consumption and expense. Which of the following is the best choice of lighting selection for this portion of the center. A. ambient lighting B. general illumination C. task lighting D. accent lighting

What is the heating value of propane? A. 1,050 btu/cubic ft, B. 120,000 btu/cubic ft C. 138,500 btu/cubic ftm D. 3,200 btu/cubic ft E. 2,500 btu/cubic ft

Which type of soil has a greater angle of repose, the internal angle between the surface of the pile and the horizontal surface? A. wet clay, B. wet sand C. dry gravel with sand, D. dry sand

Which of the following operating systems responds to all calls in one direction, then answers all calls in the reverse direction, ultimately returning the cab to the lobby. A. single automatic, B. selective collective operation, C. group automatic operation

The special connection hardware in this image is a A. joist hanger, B. post cap, C. post base D. saddle hanger, E. U hanger

What type of valve is this? It is one of the family of quarter-turn valves and is preferred for shut-off applications. A. butterfly, B. ball C. check, D. globe, E. gate

What are the causes of internal loads to buildings? (Choose 3) A. equipment, B. sunlight, C. artificial lighting, D. people E. air temperature

How does the crown molding meet at this interior angle? (Choose 2) A. mitered joint,  B. coped joint C. scribed joint,   D. scarf joint

Interior finishes for walls and ceilings are subject to testing requirements for flame spread and for smoke developed. The Steiner Tunnel Test is alternatively identified as which testing methods (choose 3): A . ASTM E84, B . UL 723, C. NFPA 253, D . NFPA 255, E . ASTM E662

In a multi-story building, maximum drift and associated accelerations usually occur where?

Which of the following spaces do local zoning codes often define as open to the public? A. Court, B. Yard C. Plaza, D. Arcade

In closing out the project delivery process, what is the most likely claim if the architect does not prepare a final change order to adjust the contract sum when the cost of the work is more or less than the specified allowance?

What is the recommended minimum slope on a green roof? A. 1.0% B. 1.5% C. 2.0% D. 2.5% E. 3.0%

Although a project attempting to meet LEED requirements for VOC limits in paints, coatings and adhesives has called for specific content limits in all applicable project specifications, what is an easily overlooked set of products that may jeopardize compliance with VOC limits in the project?

If the average outdoor temperature in a particular location for a 24-hour period is 44 degrees, what is the number of degree days?

The liability of the shareholders of "Acme" architecture corp. is limited to their share of the ownership of the firm. However, the state in which the firm is located requires that professionals including doctors, lawyers, and architects must form what type of corporation to recognize the professional liability of such licensees? A. PLLC, B. PC, C. S-Corp., D. LP

A pattern in which the units overlap less than 1/4 unit must follow reinforcing requirements for which bond?

The daylight factor method (CIE - E.U.) calculates how much daylight reaches any location in a room assuming overcast/diffuse conditions; and can account for corner windows, which cannot be accounted for using the lumen method (IES - U.S.). When 2,200 fc is measured on the ground outside, what is the resulting illumination level if one end of a room has a daylight factor of 2?

Which site class is the basis for all formulas and map values? A, B, C, D, E, or F

When a roof drain becomes blocked, water is allowed to accumulate. IBC Chapter 16 requires that roofs should be designed to account for this potential load. How is the anticipated depth of water determined?

Select the qualities of quartersawn lumber: (Select 3) A. Tends to have raised grain, B. More even grain pattern, C. Less affected by surface checks, D. Wears unevenly, E. Wears more evenly, less warping, F. Shrinks/expands less in thickness than in width

Which of the following is NOT true of site vegetation? A. up to 90% of light energy falling on vegetation is absorbed, B. capable of reducing wind speed below 10%, C. potential 15deg. F reduction of daytime temperature, D. can increase or retain fog

What is the preferred preliminary measure of hurricane intensity? A. Modified Mercalli Intensity scale, B. "mean recurrence interval" or "return period" of 50-year storm, C. Saffir-Simpson scale, D. Richter scale

Solving for reactions on a beam, a concentrated load acting at midpoint is equivalent to a: A. uniformly distributed load of equal magnitude, B. uniformly distributed load of equal magnitude acting at midpoint, C. uniform load of one half magnitude acting at midpoint, D. concentrated load of half magnitude acting at midpoint

What is the required minimum corridor width for a corridor shared between 50 persons from  Business and 250 persons from Hospital occupancy? A. 44 inches,  B. 56 inches, C. 60 inches,  D. 96 inches

Which of the following framing systems can be built using either steel or concrete? A. moment resisting   B. trussed tube C. framed tube   D.  chevron braced

Which of the following symbols is defined as  Total length of beam between reaction points, inches:  W, a, b, w, l, x, L

Which of the following are not governmental agencies? HUD, NFPA, EPA, OSHA, FEMA

5.0 With ARE 5.0 here and 4.0 phasing out by June 30, 2018, NCARB's  transition calculator provides a nice comparison of the two series. For instance, Site Planning & Design passed under 4.0 would receive credit within 2 divisions under 5.0: Programming & Analysis  Project Planning & Design Even if the transition doesn't impact your testing situation, the calculator is useful to understand how 4.0 divisions are mapped to 5.0. The content itself is not substantially different. Will ARE 5.0 change your strategy?